Author |
Message |
< 16ga. Ammunition & Reloading ~ low pressure loads for RGL and Claybuster |
|
Posted:
Wed Apr 23, 2014 5:12 am
|
|
|
Joined: 19 Apr 2014
Posts: 431
Location: Maine
|
|
Trying to wade thru all the pages here to find some info so I'll take the easy way out and ask some questions that you guys have probably answered numerous times in the past. I'm swimming in RGL hulls and 1oz CB wads. I'm looking looking for a pleasant to shoot low recoil 1oz load using Green Dot, Universal, Etc. Tried Longshot but had a fairly good bite to it. Also looking for a 7/8 oz low recoil load with the RGL.
Purchased a 16ga manual from BP but it had 1 recipe in the book for RGLs.
Thanks for your help. |
_________________ If it weren't for women cats would be extinct. |
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed Apr 23, 2014 7:46 am
|
|
|
Member
![Member Member](images/theavatar.jpg)
Joined: 09 Jan 2013
Posts: 2175
Location: Florida
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed Apr 23, 2014 9:38 am
|
|
|
Joined: 19 Apr 2014
Posts: 431
Location: Maine
|
|
My error at the start. Looking for low recoil.
Thanks |
_________________ If it weren't for women cats would be extinct. |
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed Apr 23, 2014 10:02 am
|
|
|
Member
![Member Member](images/theavatar.jpg)
Joined: 16 Nov 2006
Posts: 1338
|
|
![Rolling Eyes](images/smiles/icon_rolleyes.gif) |
Last edited by mike campbell on Sun Aug 11, 2019 12:58 pm; edited 1 time in total |
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed Apr 23, 2014 11:38 am
|
|
|
Member
![Member Member](images/theavatar.jpg)
Joined: 03 Dec 2006
Posts: 759
Location: Somewhere in the Socialist State of Minnesota
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed Apr 23, 2014 1:49 pm
|
|
|
Member
![Member Member](images/theavatar.jpg)
Joined: 12 Mar 2005
Posts: 6535
Location: massachusetts
|
|
Even 1100 FPS 1 ounce loads can push you around if they are used for higher volume shooting out of a light gun. There is a great alternative. Try 16 grains of Green Dot under a 7/8 or 3/4 ounce shot load with any standard strength 209 primer.
The Claybuster 16 ga wad shot cup is too deep for any load less than 1 ounce. It will actually accommodate 1-1/8 ounces of shot. However, one to three 1/8 inch thick (.135") 28 gauge card wads placed in the shot cup first as needed will nicely fill up the unused space. With fillers, the CB wad will serve as well as the DR16 wad which is similar in all ways except for the shot cup depth. Crimps will be perfect and recoil will be reduced to the point of being almost unnoticeable.
These light for gauge loads pattern superbly and smash targets just as well as any 1 ounce load. Great for smaller game birds too. Give them a try. Good luck. |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed Apr 23, 2014 2:44 pm
|
|
|
Member
![Member Member](images/theavatar.jpg)
Joined: 03 Dec 2006
Posts: 759
Location: Somewhere in the Socialist State of Minnesota
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed Apr 23, 2014 2:48 pm
|
|
|
Joined: 19 Apr 2014
Posts: 431
Location: Maine
|
|
Thanks for the replies. |
_________________ If it weren't for women cats would be extinct. |
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Wed Apr 23, 2014 4:45 pm
|
|
|
Joined: 10 Feb 2011
Posts: 217
Location: Pacific Northwest
|
|
oldhunter wrote: |
Which of these primers do you consider standard strength.
|
Oh Lord, please let's not have the primer discussion yet again. |
_________________ Matt
Nothing makes a gun more effective than practice. |
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Thu Apr 24, 2014 3:30 am
|
|
|
Joined: 27 Apr 2005
Posts: 380
Location: Northeast Ohio
|
|
oldhunter wrote: |
No more of these RGL's
|
Oldhunter...are you saying the RGLs are no longer being produced, or that you are just out of them in your personal supply presently?
I know I don't see them as often in the stores lately, but I hadn't heard they were out of production. I'm expecting to stock up in the fall, which is when they usually are more abundant. |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Thu Apr 24, 2014 5:49 am
|
|
|
Member
![Member Member](images/theavatar.jpg)
Joined: 06 Nov 2005
Posts: 328
|
|
I believe the old one is poking fun at recoil shyness. |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Thu Apr 24, 2014 9:59 am
|
|
|
Member
![Member Member](images/theavatar.jpg)
Joined: 03 Dec 2006
Posts: 759
Location: Somewhere in the Socialist State of Minnesota
|
|
Yes just poking a little humor in. As far as buying shells, I wouldn't know what is available. Haven't bought any new shells in over five years. Right now I'm going through another thousand hulls I picked up this week. 16 gauge, 12 gauge and 20 gauge. The only thing I have to buy is shot and I get that off of Craigs List. Get some good buys there. |
_________________ http://uk.groups.yahoo.com/group/reloading16gauge/
Minnesota Gun Owners http://gocra.org/ |
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Thu Apr 24, 2014 12:44 pm
|
|
|
Joined: 19 Apr 2014
Posts: 431
Location: Maine
|
|
16gaugeguy on that load you suggested 16gr GreenDot 7/8 oz 209 primer what do you suggest for a wad.
Thanks
Just tried a load a fellow had out the skeet club of 15.3 gr Green Dot 7/8oz lead W209 SG16 wad User friendly |
_________________ If it weren't for women cats would be extinct. |
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Fri Apr 25, 2014 1:40 pm
|
|
|
Member
![Member Member](images/theavatar.jpg)
Joined: 12 Mar 2005
Posts: 6535
Location: massachusetts
|
|
Use your CB wads with filler wads. They fit the RGL hulls very well. The SG16 wads are designed for Cheddite hulls which have a considerably bigger inside diameter than the RGL hulls. Another good alternative is the DR16 wad from Down Range. They won't need filler wads. Of course, the Remington SP16 and RP 16 wads are also okay. Filller wads will be needed with either.
With RGL hulls, I advise against choosing any of the European style 16 ga wads like the SG Gualandi, Cheddite, or Z wads. These wads are designed for Cheddite type hulls which have a larger inside diameter than the Remington hulls. The wads fit too tight, are hard to seat, and bulge or even occasionally split the RGL hulls. The overly tight fit increases the wad pull which can adversely affect pressures. |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|
Posted:
Sat Apr 26, 2014 8:39 am
|
|
|
Member
![Member Member](images/theavatar.jpg)
Joined: 12 Mar 2005
Posts: 6535
Location: massachusetts
|
|
renaudnw wrote: |
oldhunter wrote: |
Which of these primers do you consider standard strength.
|
Oh Lord, please let's not have the primer discussion yet again.
|
Don't worry. Not going to happen. ![Wink](images/smiles/icon_wink.gif) |
|
|
|
|
|
![](templates/NoseBleed/images/spacer.gif) |
|