| Author |
Message |
| < 16ga. Ammunition & Reloading ~ DR Wad load Data Question |
|
 Posted:
Fri Apr 05, 2024 10:37 am
|
|
|
Joined: 27 Aug 2020
Posts: 112
Location: SE TX Marsh and Young County Tx
|
|
Where does everyone get their load recipes for this wad at? Searching around for 7/8 and or 3/4 oz loads in the 1250 -1300 fps range.
Thanks! |
|
|
|
|
|
 |
|
| Posted:
Fri Apr 05, 2024 10:59 am
|
|
|
Joined: 04 Mar 2019
Posts: 1899
Location: Central ND
|
|
Mostly from loads that we, the members of 16ga.com, had tested. They are probably on the spreadsheets.
I am not sure that any powder company has tested loads using the the DR16.
Here are mine. If the velocities are a bit stiff, you can back the loads down a grain or two.
Tested by Tom Armbrust:
Cheddite hull
Winchester 209
18.0 grains American Select
DR16
3/4 oz. lead shot
1,339 FPS 9480 PSI
-----
Cheddite hull
Winchester 209
23.0 grains Universal
DR16
7/8 oz. lead shot
1,424 FPS 11,180 PSI
-----
Federal hull
Federal 209A
22.0 grains Universal
DR16
7/8 oz. lead shot
1,384 FPS 10820 PSI
Tested by Precision Reloading:
Federal hull
Winchester 209
16.0 grains 700-X
DR16
7/8 oz. lead shot
1,260 FPS 8,163 PSI |
_________________
Mark...You are entitled to your own opinion. You aren't entitled to your own facts. |
|
|
|
|
|
|
| Posted:
Fri Apr 05, 2024 11:24 am
|
|
|
Member
Joined: 09 Jan 2013
Posts: 2182
Location: Florida
|
|
|
|
|
|
|
| Posted:
Fri Apr 05, 2024 12:30 pm
|
|
|
Joined: 04 Mar 2019
Posts: 1899
Location: Central ND
|
|
| Yes but kinda like mine, mostly using powders that you can't get. |
_________________
Mark...You are entitled to your own opinion. You aren't entitled to your own facts. |
|
|
|
|
|
|
| Posted:
Fri Apr 05, 2024 2:03 pm
|
|
|
Member
Joined: 09 Jan 2013
Posts: 2182
Location: Florida
|
|
| Yes, you are right, did not think about that. |
|
|
|
|
|
|
|
| Posted:
Fri Apr 05, 2024 2:59 pm
|
|
|
Joined: 13 Oct 2015
Posts: 154
Location: SE Ks
|
|
| Still using 16.0 International here, around 1170 fps depending on primer. |
|
|
|
|
|
|
|
| Posted:
Fri Apr 05, 2024 3:00 pm
|
|
|
Joined: 09 Mar 2016
Posts: 760
Location: Mn.
|
|
Tested by Precision a year ago
New Green lid Green Dot 16.0 gr.
7/8 oz. weighed #8 Heper shot
DR16
Fed Hull
F209A Primer
1252 fps 9240 PSI
SD 8 fps EV 18 fps |
|
|
|
|
|
|
|
| Posted:
Fri Apr 05, 2024 6:45 pm
|
|
|
Joined: 27 Aug 2020
Posts: 112
Location: SE TX Marsh and Young County Tx
|
|
THANKS Everyone!
Have a Great Weekend! |
|
|
|
|
|
|
|
| Posted:
Sat Apr 06, 2024 8:05 am
|
|
|
Joined: 30 Sep 2019
Posts: 160
Location: Colorado
|
|
| ole_270 wrote: |
|
Still using 16.0 International here, around 1170 fps depending on primer.
|
Yes, my “go to” load for several years now in classic short chambered 16ga SxS’s has been 15.9gr of Int for 1150 using Ched 209’s.
Now we just need to get International back in stock.  |
|
|
|
|
|
|
|
| Posted:
Sun Apr 07, 2024 2:34 pm
|
|
|
Joined: 06 Jan 2017
Posts: 95
|
|
Here's the recipe I've posted here before. And with DR-16's on the way, I'll be able to it again. Tested by Tom Armbrust several years ago:
Cheddite hull (Herters). Cheddite primer, 17.3 grains 20/28, 7/8 oz shot.
Avg velocity1182 fps
Avg pressure: 7420 psi. |
|
|
|
|
|
|
|
| Posted:
Sun Apr 07, 2024 2:36 pm
|
|
|
Joined: 06 Jan 2017
Posts: 95
|
|
| Have we heard whether this will be the very last run of DR-16's? |
|
|
|
|
|
|
|
| Posted:
Mon Apr 08, 2024 4:23 am
|
|
|
Joined: 21 Mar 2013
Posts: 117
Location: Northern New Jersey
|
|
| Larry, it does not get better than that! Even better, I have a few pounds of 20/28! |
_________________
So many guns, so little time! |
|
|
|
|
|
|
| Posted:
Mon Apr 08, 2024 7:53 am
|
|
|
Joined: 04 Mar 2019
Posts: 1899
Location: Central ND
|
|
Builder,
Charles Hammack, posted earlier this year that if you wanted DR16 wads, this would be the time to buy them and stock up.
http://16ga.com/forum/viewtopic.php?t=25375&start=0 |
_________________
Mark...You are entitled to your own opinion. You aren't entitled to your own facts. |
|
|
|
|
|
|
| Posted:
Mon Apr 08, 2024 7:59 am
|
|
|
Joined: 30 Sep 2019
Posts: 160
Location: Colorado
|
|
| lbrown wrote: |
Here's the recipe I've posted here before. And with DR-16's on the way, I'll be able to it again. Tested by Tom Armbrust several years ago:
Cheddite hull (Herters). Cheddite primer, 17.3 grains 20/28, 7/8 oz shot.
Avg velocity1182 fps
Avg pressure: 7420 psi.
|
Thanks for that, Larry. I may have to pick up some 20/28 while its available as I wonder if Hodgdon is going to come through with International in ‘24 as promised. |
|
|
|
|
|
|
|
| Posted:
Mon Apr 08, 2024 8:08 am
|
|
|
Joined: 04 Mar 2019
Posts: 1899
Location: Central ND
|
|
FallCreekFan,
Hodgdon really didn't promise Clays, International or Universal for 2024. Their statement for those powders was vague and only hinted they might be made in 2024.
I would highly doubt that we will see any flake shotshell powders from Hodgdon this year unless the wars that Ukraine and Israel are fighting are quickly resolved.
It's either ball powders from Hodgdon, Alliant's sporadic release of shotshell powders, or Vihtavuori powders that we actually have access to. |
_________________
Mark...You are entitled to your own opinion. You aren't entitled to your own facts. |
|
|
|
|
|
|
